 DDR V1.13 25cee80c4f cym 23/08/11-09:31:58
LPDDR4X, 2112MHz
channel[0] BW=16 Col=10 Bk=8 CS0 Row=17 CS1 Row=17 CS=2 Die BW=16 Size=4096MB
channel[1] BW=16 Col=10 Bk=8 CS0 Row=17 CS1 Row=17 CS=2 Die BW=16 Size=4096MB
channel[2] BW=16 Col=10 Bk=8 CS0 Row=17 CS1 Row=17 CS=2 Die BW=16 Size=4096MB
channel[3] BW=16 Col=10 Bk=8 CS0 Row=17 CS1 Row=17 CS=2 Die BW=16 Size=4096MB
Manufacturer ID:0xff
CH0 RX Vref:27.9%, TX Vref:22.8%,21.8%
CH1 RX Vref:27.9%, TX Vref:23.8%,22.8%
CH2 RX Vref:27.1%, TX Vref:20.8%,20.8%
CH3 RX Vref:27.1%, TX Vref:22.8%,21.8%
change to F1: 528MHz
change to F2: 1068MHz
change to F3: 1560MHz
change to F0: 2112MHz
out
U-Boot SPL board init
U-Boot SPL 2017.09-g5f53abfa1e-221223 #zzz (Dec 26 2022 - 09:10:09)
unknown raw ID 0 0 0
unrecognized JEDEC id bytes: 00, 00, 00
Trying to boot from MMC2
mmc_init: -95, time 2201
spl: mmc init failed with error: -95
Trying to boot from MMC1
No misc partition
Trying fit image at 0x4000 sector
## Verified-boot: 0
## Checking atf-1 0x00040000 ... sha256(c902200be1...) + OK
## Checking uboot 0x00200000 ... sha256(d39c36f7a4...) + OK
## Checking fdt 0x00343fa8 ... sha256(8ecccd16d2...) + OK
## Checking atf-2 0x000f0000 ... sha256(aa71013e72...) + OK
## Checking atf-3 0xff100000 ... sha256(225d6bf071...) + OK
## Checking optee 0x08400000 ... sha256(66e30bf9e8...) + OK
Jumping to U-Boot(0x00200000) via ARM Trusted Firmware(0x00040000)
Total: 2319.572 ms

INFO:    Preloader serial: 2
NOTICE:  BL31: v2.3():v2.3-639-g87bcc5dfe:derrick.huang
NOTICE:  BL31: Built : 18:06:16, Sep  9 2023
INFO:    spec: 0x13
INFO:    ext 32k is valid
INFO:    ddr: stride-en 4CH
INFO:    GICv3 without legacy support detected.
INFO:    ARM GICv3 driver initialized in EL3
INFO:    valid_cpu_msk=0xff bcore0_rst = 0x0, bcore1_rst = 0x0
INFO:    l3 cache partition cfg-0
INFO:    system boots from cpu-hwid-0
INFO:    idle_st=0x21fff, pd_st=0x11fff9, repair_st=0xfff70001
INFO:    dfs DDR fsp_params[0].freq_mhz= 2112MHz
INFO:    dfs DDR fsp_params[1].freq_mhz= 528MHz
INFO:    dfs DDR fsp_params[2].freq_mhz= 1068MHz
INFO:    dfs DDR fsp_params[3].freq_mhz= 1560MHz
INFO:    BL31: Initialising Exception Handling Framework
INFO:    BL31: Initializing runtime services
INFO:    BL31: Initializing BL32
I/TC: 
I/TC: OP-TEE version: 3.13.0-743-gb5340fd65 #hisping.lin (gcc version 10.2.1 20201103 (GNU Toolchain for the A-profile Architecture 10.2-2020.11 (arm-10.16))) #6 Mon Aug 28 18:01:38 CST 2023 aarch64
I/TC: Primary CPU initializing
I/TC: Primary CPU switching to normal world boot
INFO:    BL31: Preparing for EL3 exit to normal world
INFO:    Entry point address = 0x200000
INFO:    SPSR = 0x3c9


U-Boot 2017.09-g4574b07dd1-230625 #dev (Dec 10 2023 - 09:20:48 +0800)

Model: Rockchip RK3588 Evaluation Board
MPIDR: 0x81000000
PreSerial: 2, raw, 0xfeb50000
DRAM:  16 GiB
Sysmem: init
Relocation Offset: eda1a000
Relocation fdt: eb9fac80 - eb9fecd8
CR: M/C/I
Using default environment

DM: v2
mmc@fe2c0000: 1, mmc@fe2e0000: 0
Bootdev(atags): mmc 0
MMC0: HS400 Enhanced Strobe, 200Mhz
PartType: EFI
224254 bytes read in 9 ms (23.8 MiB/s)
DTB(Distro): rk-kernel.dtb
No misc partition
boot mode: None
Error binding driver 'fixed regulator': -22
Some drivers failed to bind
I2c0 speed: 100000Hz
vsel-gpios- not found!
en-gpios- not found!
vdd_cpu_big0_s0 800000 uV
vsel-gpios- not found!
en-gpios- not found!
vdd_cpu_big1_s0 800000 uV
I2c1 speed: 100000Hz
vsel-gpios- not found!
en-gpios- not found!
vdd_npu_s0 800000 uV
spi2: RK806: 2
ON=0x00, OFF=0x00
vdd_gpu_s0 750000 uV
vdd_cpu_lit_s0 750000 uV
vdd_vdenc_s0 init 750000 uV
get vp0 plane mask:0x5, primary id:2, cursor_plane:0, from dts
get vp1 plane mask:0xa, primary id:3, cursor_plane:1, from dts
get vp2 plane mask:0x140, primary id:8, cursor_plane:6, from dts
get vp3 plane mask:0x280, primary id:9, cursor_plane:7, from dts
Could not find baseparameter partition
Model: Embedfire LubanCat-4
MPIDR: 0x81000000
No resource file: logo.bmp
512 bytes read in 2 ms (250 KiB/s)
logo(Distro): logo.bmp
1215954 bytes read in 10 ms (116 MiB/s)
logo(Distro): logo.bmp
Rockchip UBOOT DRM driver version: v1.0.1
vp0 have layer nr:2[0 2 ], primary plane: 2
vp1 have layer nr:2[1 3 ], primary plane: 3
vp2 have layer nr:2[6 8 ], primary plane: 8
vp3 have layer nr:2[7 9 ], primary plane: 9
phy@fed80000: mode 0x02 is not support
hdmi@fde80000 disconnected
CLK: (sync kernel. arm: enter 1008000 KHz, init 1008000 KHz, kernel 0N/A)
  b0pll 24000 KHz
  b1pll 24000 KHz
  lpll 24000 KHz
  v0pll 24000 KHz
  aupll 786431 KHz
  cpll 1500000 KHz
  gpll 1188000 KHz
  npll 850000 KHz
  ppll 1100000 KHz
  aclk_center_root 702000 KHz
  pclk_center_root 100000 KHz
  hclk_center_root 396000 KHz
  aclk_center_low_root 500000 KHz
  aclk_top_root 750000 KHz
  pclk_top_root 100000 KHz
  aclk_low_top_root 396000 KHz
Net:   eth1: ethernet@fe1c0000
Hit key to stop autoboot('CTRL+C'):  0 
switch to partitions #0, OK
mmc1 is current device
** Unrecognized filesystem type **
switch to partitions #0, OK
mmc0(part 0) is current device
Scanning mmc 0:2...
Found U-Boot script /boot.scr
1609 bytes read in 3 ms (523.4 KiB/s)
## Executing script at 00500000
[boot.cmd] run boot.cmd scripts ...
[boot.cmd] load mmc 0:2 0x0a100000 /uEnv/uEnv.txt ...
2413 bytes read in 5 ms (470.7 KiB/s)
[boot.cmd] Importing environment from mmc ...
bootargs=storagemedia=emmc androidboot.storagemedia=emmc androidboot.mode=normal root=/dev/mmcblk0p3 earlyprintk console=ttyFIQ0 console=tty1 consoleblank=0 loglevel=7 rootwait rw rootfstype=ext4
[boot.cmd] load mmc 0:2 0x0a200000 /initrd-5.10.160 ...
7069963 bytes read in 28 ms (240.8 MiB/s)
[boot.cmd] loading mmc 0:2 0x00400000 /Image-5.10.160 ...
35199488 bytes read in 129 ms (260.2 MiB/s)
[boot.cmd] loading default rk-kernel.dtb
224254 bytes read in 9 ms (23.8 MiB/s)
[boot.cmd] dtoverlay from /uEnv/uEnv.txt
DTOVERLAY[debug]: param no:5  0x08300000  0x08000000 /uEnv/uEnv.txt 0x0a100000 

[boot.cmd] [mmc 0:2] ...
[boot.cmd] [booti] ...
Fdt Ramdisk skip relocation
No misc partition
## Loading init Ramdisk from Legacy Image at 0a200000 ...
   Image Name:   
   Image Type:   ARM Linux RAMDisk Image (gzip compressed)
   Data Size:    7069899 Bytes = 6.7 MiB
   Load Address: 00000000
   Entry Point:  00000000
   Verifying Checksum ... OK
## Flattened Device Tree blob at 0x08300000
   Booting using the fdt blob at 0x08300000
   reserving fdt memory region: addr=8300000 size=67000
   Using Device Tree in place at 0000000008300000, end 0000000008369fff
No resource file: logo_kernel.bmp
512 bytes read in 3 ms (166 KiB/s)
logo(Distro): logo.bmp
1215954 bytes read in 11 ms (105.4 MiB/s)
logo(Distro): logo.bmp
WARNING: could not set reg FDT_ERR_BADOFFSET.
## reserved-memory:
  drm-logo@00000000: addr=edf00000 size=4a4000
  ramoops@110000: addr=110000 size=f0000
Adding bank: 0x00200000 - 0x08400000 (size: 0x08200000)
Adding bank: 0x09400000 - 0xf0000000 (size: 0xe6c00000)
Adding bank: 0x100000000 - 0x3fc000000 (size: 0x2fc000000)
Adding bank: 0x3fc500000 - 0x3fff00000 (size: 0x03a00000)
Adding bank: 0x4f0000000 - 0x500000000 (size: 0x10000000)
Total: 649.871/720.326 ms

Starting kernel ...

I/TC: Secondary CPU 1 initializing
I/TC: Secondary CPU 1 switching to normal world boot
I/TC: Secondary CPU 2 initializing
I/TC: Secondary CPU 2 switching to normal world boot
I/TC: Secondary CPU 3 initializing
I/TC: Secondary CPU 3 switching to normal world boot
I/TC: Secondary CPU 4 initializing
I/TC: Secondary CPU 4 switching to normal world boot
I/TC: Secondary CPU 5 initializing
I/TC: Secondary CPU 5 switching to normal world boot
I/TC: Secondary CPU 6 initializing
I/TC: Secondary CPU 6 switching to normal world boot
I/TC: Secondary CPU 7 initializing
I/TC: Secondary CPU 7 switching to normal world boot
[    0.724598] Booting Linux on physical CPU 0x0000000000 [0x412fd050]
[    0.724616] Linux version 5.10.160 (dev@dev) (aarch64-none-linux-gnu-gcc (GNU Toolchain for the A-profile Architecture 10.3-2021.07 (arm-10.29)) 10.3.1 20210621, GNU ld (GNU Toolchain for the A-profile Architecture 10.3-2021.07 (arm-10.29)) 2.36.1.20210621) #2 SMP Sun Dec 10 09:06:08 CST 2023
[    0.733362] Machine model: Embedfire LubanCat-4
[    0.735282] efi: UEFI not found.
[    0.739818] OF: fdt: Reserved memory: failed to reserve memory for node 'drm-cubic-lut@00000000': base 0x0000000000000000, size 0 MiB
[    0.739868] Reserved memory: created CMA memory pool at 0x00000004ff800000, size 8 MiB
[    0.739873] OF: reserved mem: initialized node cma, compatible id shared-dma-pool
[    0.960811] Zone ranges:
[    0.960824]   DMA      [mem 0x0000000000200000-0x00000000ffffffff]
[    0.960833]   DMA32    empty
[    0.960838]   Normal   [mem 0x0000000100000000-0x00000004ffffffff]
[    0.960845] Movable zone start for each node
[    0.960848] Early memory node ranges
[    0.960853]   node   0: [mem 0x0000000000200000-0x00000000083fffff]
[    0.960858]   node   0: [mem 0x0000000009400000-0x00000000efffffff]
[    0.960865]   node   0: [mem 0x0000000100000000-0x00000003fbffffff]
[    0.960874]   node   0: [mem 0x00000003fc500000-0x00000003ffefffff]
[    0.960879]   node   0: [mem 0x00000004f0000000-0x00000004ffffffff]
[    0.960885] Initmem setup node 0 [mem 0x0000000000200000-0x00000004ffffffff]
[    1.054346] On node 0, zone Normal: 256 pages in unavailable ranges
[    1.054481] psci: probing for conduit method from DT.
[    1.054495] psci: PSCIv1.1 detected in firmware.
[    1.054499] psci: Using standard PSCI v0.2 function IDs
[    1.054505] psci: Trusted OS migration not required
[    1.054512] psci: SMC Calling Convention v1.2
[    1.054841] percpu: Embedded 30 pages/cpu s83736 r8192 d30952 u122880
[    1.054997] Detected VIPT I-cache on CPU0
[    1.055033] CPU features: detected: GIC system register CPU interface
[    1.055039] CPU features: detected: Virtualization Host Extensions
[    1.055047] CPU features: detected: ARM errata 1165522, 1319367, or 1530923
[    1.055060] alternatives: patching kernel code
[    1.056763] Built 1 zonelists, mobility grouping on.  Total pages: 4122720
[    1.056773] Kernel command line: storagemedia=emmc androidboot.storagemedia=emmc androidboot.mode=normal root=/dev/mmcblk0p3 earlyprintk console=ttyFIQ0 console=tty1 consoleblank=0 loglevel=7 rootwait rw rootfstype=ext4
[    1.058431] Dentry cache hash table entries: 2097152 (order: 12, 16777216 bytes, linear)
[    1.059181] Inode-cache hash table entries: 1048576 (order: 11, 8388608 bytes, linear)
[    1.059187] mem auto-init: stack:off, heap alloc:off, heap free:off
[    1.065295] software IO TLB: mapped [mem 0x00000000e9f00000-0x00000000edf00000] (64MB)
[    1.173968] Memory: 16310200K/16752640K available (18752K kernel code, 3270K rwdata, 5968K rodata, 6272K init, 555K bss, 434248K reserved, 8192K cma-reserved)
[    1.174082] SLUB: HWalign=64, Order=0-3, MinObjects=0, CPUs=8, Nodes=1
[    1.174109] ftrace: allocating 58226 entries in 228 pages
[    1.248275] ftrace: allocated 228 pages with 4 groups
[    1.248500] rcu: Hierarchical RCU implementation.
[    1.248508] rcu: 	RCU event tracing is enabled.
[    1.248513] 	Rude variant of Tasks RCU enabled.
[    1.248518] rcu: RCU calculated value of scheduler-enlistment delay is 30 jiffies.
[    1.252675] NR_IRQS: 64, nr_irqs: 64, preallocated irqs: 0
[    1.254929] GICv3: GIC: Using split EOI/Deactivate mode
[    1.254937] GICv3: 480 SPIs implemented
[    1.254941] GICv3: 0 Extended SPIs implemented
[    1.254966] GICv3: Distributor has no Range Selector support
[    1.254975] GICv3: 16 PPIs implemented
[    1.255020] GICv3: CPU0: found redistributor 0 region 0:0x00000000fe680000
[    1.255115] ITS [mem 0xfe640000-0xfe65ffff]
[    1.255160] ITS@0x00000000fe640000: allocated 8192 Devices @3fc6f0000 (indirect, esz 8, psz 64K, shr 0)
[    1.255183] ITS@0x00000000fe640000: allocated 32768 Interrupt Collections @3fc700000 (flat, esz 2, psz 64K, shr 0)
[    1.255192] ITS: using cache flushing for cmd queue
[    1.255221] ITS [mem 0xfe660000-0xfe67ffff]
[    1.255264] ITS@0x00000000fe660000: allocated 8192 Devices @3fc720000 (indirect, esz 8, psz 64K, shr 0)
[    1.255287] ITS@0x00000000fe660000: allocated 32768 Interrupt Collections @3fc730000 (flat, esz 2, psz 64K, shr 0)
[    1.255294] ITS: using cache flushing for cmd queue
[    1.255474] GICv3: using LPI property table @0x00000003fc740000
[    1.255583] GIC: using cache flushing for LPI property table
[    1.255592] GICv3: CPU0: using allocated LPI pending table @0x00000003fc750000
[    1.362956] arch_timer: cp15 timer(s) running at 24.00MHz (phys).
[    1.362965] clocksource: arch_sys_counter: mask: 0xffffffffffffff max_cycles: 0x588fe9dc0, max_idle_ns: 440795202592 ns
[    1.362975] sched_clock: 56 bits at 24MHz, resolution 41ns, wraps every 4398046511097ns
[    1.364037] Console: colour dummy device 80x25
[    1.364457] printk: console [tty1] enabled
[    1.364485] Calibrating delay loop (skipped), value calculated using timer frequency.. 48.00 BogoMIPS (lpj=80000)
[    1.364503] pid_max: default: 32768 minimum: 301
[    1.364639] Mount-cache hash table entries: 32768 (order: 6, 262144 bytes, linear)
[    1.364679] Mountpoint-cache hash table entries: 32768 (order: 6, 262144 bytes, linear)
[    1.365934] rcu: Hierarchical SRCU implementation.
[    1.366617] Platform MSI: msi-controller@fe640000 domain created
[    1.366640] Platform MSI: msi-controller@fe660000 domain created
[    1.366943] PCI/MSI: /interrupt-controller@fe600000/msi-controller@fe640000 domain created
[    1.366968] PCI/MSI: /interrupt-controller@fe600000/msi-controller@fe660000 domain created
[    1.367119] EFI services will not be available.
[    1.367413] smp: Bringing up secondary CPUs ...
[    1.368534] Detected VIPT I-cache on CPU1
[    1.368558] GICv3: CPU1: found redistributor 100 region 0:0x00000000fe6a0000
[    1.368571] GICv3: CPU1: using allocated LPI pending table @0x00000003fc760000
[    1.368606] CPU1: Booted secondary processor 0x0000000100 [0x412fd050]
[    1.369768] Detected VIPT I-cache on CPU2
[    1.369788] GICv3: CPU2: found redistributor 200 region 0:0x00000000fe6c0000
[    1.369801] GICv3: CPU2: using allocated LPI pending table @0x00000003fc770000
[    1.369835] CPU2: Booted secondary processor 0x0000000200 [0x412fd050]
[    1.370976] Detected VIPT I-cache on CPU3
[    1.370993] GICv3: CPU3: found redistributor 300 region 0:0x00000000fe6e0000
[    1.371005] GICv3: CPU3: using allocated LPI pending table @0x00000003fc780000
[    1.371037] CPU3: Booted secondary processor 0x0000000300 [0x412fd050]
[    1.372167] CPU features: detected: Spectre-v4
[    1.372170] CPU features: detected: Spectre-BHB
[    1.372171] Detected PIPT I-cache on CPU4
[    1.372182] GICv3: CPU4: found redistributor 400 region 0:0x00000000fe700000
[    1.372190] GICv3: CPU4: using allocated LPI pending table @0x00000003fc790000
[    1.372211] CPU4: Booted secondary processor 0x0000000400 [0x414fd0b0]
[    1.373309] Detected PIPT I-cache on CPU5
[    1.373320] GICv3: CPU5: found redistributor 500 region 0:0x00000000fe720000
[    1.373328] GICv3: CPU5: using allocated LPI pending table @0x00000003fc7a0000
[    1.373349] CPU5: Booted secondary processor 0x0000000500 [0x414fd0b0]
[    1.374465] Detected PIPT I-cache on CPU6
[    1.374476] GICv3: CPU6: found redistributor 600 region 0:0x00000000fe740000
[    1.374484] GICv3: CPU6: using allocated LPI pending table @0x00000003fc7b0000
[    1.374505] CPU6: Booted secondary processor 0x0000000600 [0x414fd0b0]
[    1.375600] Detected PIPT I-cache on CPU7
[    1.375612] GICv3: CPU7: found redistributor 700 region 0:0x00000000fe760000
[    1.375619] GICv3: CPU7: using allocated LPI pending table @0x00000003fc7c0000
[    1.375640] CPU7: Booted secondary processor 0x0000000700 [0x414fd0b0]
[    1.375689] smp: Brought up 1 node, 8 CPUs
[    1.375884] SMP: Total of 8 processors activated.
[    1.375892] CPU features: detected: Privileged Access Never
[    1.375901] CPU features: detected: User Access Override
[    1.375909] CPU features: detected: 32-bit EL0 Support
[    1.375917] CPU features: detected: Common not Private translations
[    1.375926] CPU features: detected: RAS Extension Support
[    1.375934] CPU features: detected: Data cache clean to the PoU not required for I/D coherence
[    1.375946] CPU features: detected: CRC32 instructions
[    1.375953] CPU features: detected: Speculative Store Bypassing Safe (SSBS)
[    1.375964] CPU features: detected: RCpc load-acquire (LDAPR)
[    1.376028] CPU: All CPU(s) started at EL2
[    1.378423] devtmpfs: initialized
[    1.387018] Registered cp15_barrier emulation handler
[    1.387028] Registered setend emulation handler
[    1.387085] clocksource: jiffies: mask: 0xffffffff max_cycles: 0xffffffff, max_idle_ns: 6370867519511994 ns
[    1.387093] futex hash table entries: 2048 (order: 5, 131072 bytes, linear)
[    1.387219] pinctrl core: initialized pinctrl subsystem
[    1.387396] DMI not present or invalid.
[    1.387563] NET: Registered protocol family 16
[    1.388324] DMA: preallocated 2048 KiB GFP_KERNEL pool for atomic allocations
[    1.388417] DMA: preallocated 2048 KiB GFP_KERNEL|GFP_DMA pool for atomic allocations
[    1.388755] Registered FIQ tty driver
[    1.388848] thermal_sys: Registered thermal governor 'fair_share'
[    1.388849] thermal_sys: Registered thermal governor 'step_wise'
[    1.388854] thermal_sys: Registered thermal governor 'user_space'
[    1.388857] thermal_sys: Registered thermal governor 'power_allocator'
[    1.388955] thermal thermal_zone1: power_allocator: sustainable_power will be estimated
[    1.388987] thermal thermal_zone2: power_allocator: sustainable_power will be estimated
[    1.389010] thermal thermal_zone3: power_allocator: sustainable_power will be estimated
[    1.389031] thermal thermal_zone4: power_allocator: sustainable_power will be estimated
[    1.389053] thermal thermal_zone5: power_allocator: sustainable_power will be estimated
[    1.389075] thermal thermal_zone6: power_allocator: sustainable_power will be estimated
[    1.389092] cpuidle: using governor menu
[    1.389158] hw-breakpoint: found 6 breakpoint and 4 watchpoint registers.
[    1.389242] ASID allocator initialised with 65536 entries
[    1.390182] ramoops: dmesg-0	0x20000@0x0000000000110000
[    1.390195] ramoops: console	0x80000@0x0000000000130000
[    1.390205] ramoops: pmsg	0x50000@0x00000000001b0000
[    1.390412] printk: console [ramoops-1] enabled
[    1.390416] pstore: Registered ramoops as persistent store backend
[    1.390421] ramoops: using 0xf0000@0x110000, ecc: 0
[    1.421107] rockchip-gpio fd8a0000.gpio: probed /pinctrl/gpio@fd8a0000
[    1.421254] rockchip-gpio fec20000.gpio: probed /pinctrl/gpio@fec20000
[    1.421386] rockchip-gpio fec30000.gpio: probed /pinctrl/gpio@fec30000
[    1.421542] rockchip-gpio fec40000.gpio: probed /pinctrl/gpio@fec40000
[    1.421700] rockchip-gpio fec50000.gpio: probed /pinctrl/gpio@fec50000
[    1.421727] rockchip-pinctrl pinctrl: probed pinctrl
[    1.429475] fiq_debugger fiq_debugger.0: IRQ fiq not found
[    1.429484] fiq_debugger fiq_debugger.0: IRQ wakeup not found
[    1.429490] fiq_debugger_probe: could not install nmi irq handler
[    1.429671] printk: console [ttyFIQ0] enabled
[    1.429735] Registered fiq debugger ttyFIQ0
[    1.429961] vcc5v0_sys: supplied by vcc5v_dcin
[    1.430044] vcc_5v0: supplied by vcc5v0_sys
[    1.430126] vcc_5v0: supplied by vcc5v0_sys
[    1.430160] debugfs: Directory 'vcc_5v0' with parent 'regulator' already present!
[    1.430168] debugfs: Directory 'vcc_5v0' with parent 'vcc_5v0' already present!
[    1.430205] vcc_1v1_nldo_s3: supplied by vcc5v0_sys
[    1.430357] vbus5v0_typec: supplied by vcc_5v0
[    1.430456] vcc5v0_usb30_host: supplied by vcc_5v0
[    1.430556] vcc5v0_usb20_host: supplied by vcc_5v0
[    1.430602] vcc3v3_pcie20: supplied by vcc5v0_sys
[    1.439472] iommu: Default domain type: Translated 
[    1.441952] SCSI subsystem initialized
[    1.442007] usbcore: registered new interface driver usbfs
[    1.442020] usbcore: registered new interface driver hub
[    1.442033] usbcore: registered new device driver usb
[    1.442060] mc: Linux media interface: v0.10
[    1.442070] videodev: Linux video capture interface: v2.00
[    1.442089] pps_core: LinuxPPS API ver. 1 registered
[    1.442093] pps_core: Software ver. 5.3.6 - Copyright 2005-2007 Rodolfo Giometti <giometti@linux.it>
[    1.442100] PTP clock support registered
[    1.442274] arm-scmi firmware:scmi: SCMI Notifications - Core Enabled.
[    1.442303] arm-scmi firmware:scmi: SCMI Protocol v2.0 'rockchip:' Firmware version 0x0
[    1.442960] Advanced Linux Sound Architecture Driver Initialized.
[    1.444323] rockchip-cpuinfo cpuinfo: SoC		: 35880000
[    1.444330] rockchip-cpuinfo cpuinfo: Serial		: f7c22d6fbabd9750
[    1.444545] clocksource: Switched to clocksource arch_sys_counter
[    1.680196] NET: Registered protocol family 2
[    1.680369] IP idents hash table entries: 262144 (order: 9, 2097152 bytes, linear)
[    1.683892] tcp_listen_portaddr_hash hash table entries: 8192 (order: 5, 131072 bytes, linear)
[    1.684037] TCP established hash table entries: 131072 (order: 8, 1048576 bytes, linear)
[    1.684680] TCP bind hash table entries: 65536 (order: 8, 1048576 bytes, linear)
[    1.685314] TCP: Hash tables configured (established 131072 bind 65536)
[    1.685352] UDP hash table entries: 8192 (order: 6, 262144 bytes, linear)
[    1.685586] UDP-Lite hash table entries: 8192 (order: 6, 262144 bytes, linear)
[    1.685862] NET: Registered protocol family 1
[    1.686093] RPC: Registered named UNIX socket transport module.
[    1.686098] RPC: Registered udp transport module.
[    1.686102] RPC: Registered tcp transport module.
[    1.686106] RPC: Registered tcp NFSv4.1 backchannel transport module.
[    1.686397] PCI: CLS 0 bytes, default 64
[    1.686603] Trying to unpack rootfs image as initramfs...
[    1.841507] Freeing initrd memory: 6900K
[    1.841816] rockchip-thermal fec00000.tsadc: Missing rockchip,grf property
[    1.842220] rockchip-thermal fec00000.tsadc: tsadc is probed successfully!
[    1.842743] hw perfevents: enabled with armv8_pmuv3 PMU driver, 7 counters available
[    1.844932] Initialise system trusted keyrings
[    1.845010] workingset: timestamp_bits=46 max_order=22 bucket_order=0
[    1.846458] squashfs: version 4.0 (2009/01/31) Phillip Lougher
[    1.846706] NFS: Registering the id_resolver key type
[    1.846720] Key type id_resolver registered
[    1.846724] Key type id_legacy registered
[    1.846731] Installing knfsd (copyright (C) 1996 okir@monad.swb.de).
[    1.846914] jffs2: version 2.2. (NAND) © 2001-2006 Red Hat, Inc.
[    1.847001] fuse: init (API version 7.32)
[    1.847095] SGI XFS with security attributes, no debug enabled
[    1.847480] NET: Registered protocol family 38
[    1.847486] Key type asymmetric registered
[    1.847490] Asymmetric key parser 'x509' registered
[    1.847503] Block layer SCSI generic (bsg) driver version 0.4 loaded (major 242)
[    1.847509] io scheduler mq-deadline registered
[    1.847513] io scheduler kyber registered
[    1.852357] rockchip-hdptx-phy-hdmi fed60000.hdmiphy: hdptx phy init success
[    1.853886] rk-pcie fe190000.pcie: invalid prsnt-gpios property in node
[    1.854008] pwm-backlight backlight0: supply power not found, using dummy regulator
[    1.854189] pwm-backlight backlight1: supply power not found, using dummy regulator
[    1.854371] rk-pcie fe190000.pcie: IRQ msi not found
[    1.854386] rk-pcie fe190000.pcie: use outband MSI support
[    1.854390] iep: Module initialized.
[    1.854399] rk-pcie fe190000.pcie: Missing *config* reg space
[    1.854420] rk-pcie fe190000.pcie: host bridge /pcie@fe190000 ranges:
[    1.854422] mpp_service mpp-srv: 1dd504da414f author: Chandler Chen 2023-06-27 video: rockchip: mpp: fix crash issue when no iommu
[    1.854425] mpp_service mpp-srv: probe start
[    1.854447] rk-pcie fe190000.pcie:      err 0x00f4000000..0x00f40fffff -> 0x00f4000000
[    1.854471] rk-pcie fe190000.pcie:       IO 0x00f4100000..0x00f41fffff -> 0x00f4100000
[    1.854493] rk-pcie fe190000.pcie:      MEM 0x00f4200000..0x00f4ffffff -> 0x00f4200000
[    1.854511] rk-pcie fe190000.pcie:      MEM 0x0a00000000..0x0a3fffffff -> 0x0a00000000
[    1.854564] rk-pcie fe190000.pcie: Missing *config* reg space
[    1.854599] rk-pcie fe190000.pcie: invalid resource
[    1.855603] mpp_vdpu2 fdb50400.vdpu: Adding to iommu group 1
[    1.855771] mpp_vdpu2 fdb50400.vdpu: probe device
[    1.855850] mpp_vdpu2 fdb50400.vdpu: reset_group->rw_sem_on=0
[    1.855857] mpp_vdpu2 fdb50400.vdpu: reset_group->rw_sem_on=0
[    1.855948] mpp_vdpu2 fdb50400.vdpu: probing finish
[    1.856071] mpp_vepu2 jpege-ccu: probing start
[    1.856076] mpp_vepu2 jpege-ccu: probing finish
[    1.856138] mpp_vepu2 fdb50000.vepu: Adding to iommu group 1
[    1.856207] mpp_vepu2 fdb50000.vepu: probing start
[    1.856267] mpp_vepu2 fdb50000.vepu: reset_group->rw_sem_on=0
[    1.856272] mpp_vepu2 fdb50000.vepu: reset_group->rw_sem_on=0
[    1.856363] mpp_vepu2 fdb50000.vepu: probing finish
[    1.856444] mpp_vepu2 fdba0000.jpege-core: Adding to iommu group 5
[    1.856560] mpp_vepu2 fdba0000.jpege-core: probing start
[    1.856632] mpp_vepu2 fdba0000.jpege-core: attach ccu success
[    1.856722] mpp_vepu2 fdba0000.jpege-core: probing finish
[    1.856796] mpp_vepu2 fdba4000.jpege-core: Adding to iommu group 6
[    1.856911] mpp_vepu2 fdba4000.jpege-core: probing start
[    1.856979] mpp_vepu2 fdba4000.jpege-core: attach ccu success
[    1.857070] mpp_vepu2 fdba4000.jpege-core: probing finish
[    1.857146] mpp_vepu2 fdba8000.jpege-core: Adding to iommu group 7
[    1.857278] mpp_vepu2 fdba8000.jpege-core: probing start
[    1.857343] mpp_vepu2 fdba8000.jpege-core: attach ccu success
[    1.857428] mpp_vepu2 fdba8000.jpege-core: probing finish
[    1.857504] mpp_vepu2 fdbac000.jpege-core: Adding to iommu group 8
[    1.857615] mpp_vepu2 fdbac000.jpege-core: probing start
[    1.857680] mpp_vepu2 fdbac000.jpege-core: attach ccu success
[    1.857764] mpp_vepu2 fdbac000.jpege-core: probing finish
[    1.857948] mpp-iep2 fdbb0000.iep: Adding to iommu group 9
[    1.858061] mpp-iep2 fdbb0000.iep: probe device
[    1.858145] mpp-iep2 fdbb0000.iep: allocate roi buffer failed
[    1.858226] mpp-iep2 fdbb0000.iep: probing finish
[    1.858373] mpp_jpgdec fdb90000.jpegd: Adding to iommu group 4
[    1.858537] mpp_jpgdec fdb90000.jpegd: probe device
[    1.858695] mpp_jpgdec fdb90000.jpegd: probing finish
[    1.858932] mpp_rkvdec2 fdc30000.rkvdec-ccu: rkvdec-ccu, probing start
[    1.858972] mpp_rkvdec2 fdc30000.rkvdec-ccu: ccu-mode: 1
[    1.858977] mpp_rkvdec2 fdc30000.rkvdec-ccu: probing finish
[    1.859032] mpp_rkvdec2 fdc38100.rkvdec-core: Adding to iommu group 12
[    1.859231] mpp_rkvdec2 fdc38100.rkvdec-core: rkvdec-core, probing start
[    1.859308] mpp_rkvdec2 fdc38100.rkvdec-core: shared_niu_a is not found!
[    1.859314] rkvdec2_init:1022: No niu aclk reset resource define
[    1.859319] mpp_rkvdec2 fdc38100.rkvdec-core: shared_niu_h is not found!
[    1.859323] rkvdec2_init:1025: No niu hclk reset resource define
[    1.859344] mpp_rkvdec2 fdc38100.rkvdec-core: no regulator, devfreq is disabled
[    1.859391] mpp_rkvdec2 fdc38100.rkvdec-core: core_mask=00010001
[    1.859396] mpp_rkvdec2 fdc38100.rkvdec-core: attach ccu as core 0
[    1.859522] mpp_rkvdec2 fdc38100.rkvdec-core: sram_start 0x00000000ff001000
[    1.859527] mpp_rkvdec2 fdc38100.rkvdec-core: rcb_iova 0x00000000fff00000
[    1.859532] mpp_rkvdec2 fdc38100.rkvdec-core: sram_size 491520
[    1.859536] mpp_rkvdec2 fdc38100.rkvdec-core: rcb_size 1048576
[    1.859541] mpp_rkvdec2 fdc38100.rkvdec-core: min_width 512
[    1.859547] mpp_rkvdec2 fdc38100.rkvdec-core: rcb_info_count 20
[    1.859551] mpp_rkvdec2 fdc38100.rkvdec-core: [136, 24576]
[    1.859556] mpp_rkvdec2 fdc38100.rkvdec-core: [137, 49152]
[    1.859560] mpp_rkvdec2 fdc38100.rkvdec-core: [141, 90112]
[    1.859564] mpp_rkvdec2 fdc38100.rkvdec-core: [140, 49152]
[    1.859569] mpp_rkvdec2 fdc38100.rkvdec-core: [139, 180224]
[    1.859573] mpp_rkvdec2 fdc38100.rkvdec-core: [133, 49152]
[    1.859578] mpp_rkvdec2 fdc38100.rkvdec-core: [134, 8192]
[    1.859582] mpp_rkvdec2 fdc38100.rkvdec-core: [135, 4352]
[    1.859586] mpp_rkvdec2 fdc38100.rkvdec-core: [138, 13056]
[    1.859591] mpp_rkvdec2 fdc38100.rkvdec-core: [142, 291584]
[    1.859614] mpp_rkvdec2 fdc38100.rkvdec-core: probing finish
[    1.859662] mpp_rkvdec2 fdc48100.rkvdec-core: Adding to iommu group 13
[    1.859843] mpp_rkvdec2 fdc48100.rkvdec-core: rkvdec-core, probing start
[    1.859920] mpp_rkvdec2 fdc48100.rkvdec-core: shared_niu_a is not found!
[    1.859924] rkvdec2_init:1022: No niu aclk reset resource define
[    1.859929] mpp_rkvdec2 fdc48100.rkvdec-core: shared_niu_h is not found!
[    1.859934] rkvdec2_init:1025: No niu hclk reset resource define
[    1.859953] mpp_rkvdec2 fdc48100.rkvdec-core: no regulator, devfreq is disabled
[    1.859987] mpp_rkvdec2 fdc48100.rkvdec-core: core_mask=00020002
[    1.860004] mpp_rkvdec2 fdc48100.rkvdec-core: attach ccu as core 1
[    1.860151] mpp_rkvdec2 fdc48100.rkvdec-core: sram_start 0x00000000ff079000
[    1.860156] mpp_rkvdec2 fdc48100.rkvdec-core: rcb_iova 0x00000000ffe00000
[    1.860160] mpp_rkvdec2 fdc48100.rkvdec-core: sram_size 487424
[    1.860165] mpp_rkvdec2 fdc48100.rkvdec-core: rcb_size 1048576
[    1.860170] mpp_rkvdec2 fdc48100.rkvdec-core: min_width 512
[    1.860175] mpp_rkvdec2 fdc48100.rkvdec-core: rcb_info_count 20
[    1.860180] mpp_rkvdec2 fdc48100.rkvdec-core: [136, 24576]
[    1.860184] mpp_rkvdec2 fdc48100.rkvdec-core: [137, 49152]
[    1.860189] mpp_rkvdec2 fdc48100.rkvdec-core: [141, 90112]
[    1.860193] mpp_rkvdec2 fdc48100.rkvdec-core: [140, 49152]
[    1.860197] mpp_rkvdec2 fdc48100.rkvdec-core: [139, 180224]
[    1.860202] mpp_rkvdec2 fdc48100.rkvdec-core: [133, 49152]
[    1.860206] mpp_rkvdec2 fdc48100.rkvdec-core: [134, 8192]
[    1.860210] mpp_rkvdec2 fdc48100.rkvdec-core: [135, 4352]
[    1.860215] mpp_rkvdec2 fdc48100.rkvdec-core: [138, 13056]
[    1.860219] mpp_rkvdec2 fdc48100.rkvdec-core: [142, 291584]
[    1.860239] mpp_rkvdec2 fdc48100.rkvdec-core: probing finish
[    1.860341] mpp_rkvenc2 rkvenc-ccu: probing start
[    1.860346] mpp_rkvenc2 rkvenc-ccu: probing finish
[    1.860430] mpp_rkvenc2 fdbd0000.rkvenc-core: Adding to iommu group 10
[    1.860570] mpp_rkvenc2 fdbd0000.rkvenc-core: probing start
[    1.860676] mpp_rkvenc2 fdbd0000.rkvenc-core: dev_pm_opp_set_regulators: no regulator (venc) found: -19
[    1.860693] rkvenc_init:1859: failed to add venc devfreq
[    1.860714] mpp_rkvenc2 fdbd0000.rkvenc-core: attach ccu as core 0
[    1.860833] mpp_rkvenc2 fdbd0000.rkvenc-core: probing finish
[    1.860878] mpp_rkvenc2 fdbe0000.rkvenc-core: Adding to iommu group 11
[    1.861023] mpp_rkvenc2 fdbe0000.rkvenc-core: probing start
[    1.861112] mpp_rkvenc2 fdbe0000.rkvenc-core: dev_pm_opp_set_regulators: no regulator (venc) found: -19
[    1.861123] rkvenc_init:1859: failed to add venc devfreq
[    1.861164] mpp_rkvenc2 fdbe0000.rkvenc-core: attach ccu as core 1
[    1.861346] mpp_rkvenc2 fdbe0000.rkvenc-core: probing finish
[    1.861698] mpp_av1dec: Adding child /av1d@fdc70000
[    1.861748] mpp_av1dec: register device av1d-master
[    1.861770] mpp_av1dec av1d-master: av1_iommu_of_xlate,784
[    1.861784] av1_iommu_probe_device,736, consumer : av1d-master, supplier : fdca0000.iommu
[    1.861810] mpp_av1dec av1d-master: Adding to iommu group 15
[    1.861993] mpp_av1dec av1d-master: probing start
[    1.862159] mpp_av1dec av1d-master: probing finish
[    1.862183] mpp_service mpp-srv: probe success
[    1.868469] dma-pl330 fea10000.dma-controller: Loaded driver for PL330 DMAC-241330
[    1.868480] dma-pl330 fea10000.dma-controller: 	DBUFF-128x8bytes Num_Chans-8 Num_Peri-32 Num_Events-16
[    1.869059] dma-pl330 fea30000.dma-controller: Loaded driver for PL330 DMAC-241330
[    1.869067] dma-pl330 fea30000.dma-controller: 	DBUFF-128x8bytes Num_Chans-8 Num_Peri-32 Num_Events-16
[    1.869647] dma-pl330 fed10000.dma-controller: Loaded driver for PL330 DMAC-241330
[    1.869656] dma-pl330 fed10000.dma-controller: 	DBUFF-128x8bytes Num_Chans-8 Num_Peri-32 Num_Events-16
[    1.869821] rockchip-pvtm fda40000.pvtm: pvtm@0 probed
[    1.869859] rockchip-pvtm fda50000.pvtm: pvtm@1 probed
[    1.869893] rockchip-pvtm fda60000.pvtm: pvtm@2 probed
[    1.869934] rockchip-pvtm fdaf0000.pvtm: pvtm@3 probed
[    1.869965] rockchip-pvtm fdb30000.pvtm: pvtm@4 probed
[    1.870152] rockchip-system-monitor rockchip-system-monitor: system monitor probe
[    1.870745] Serial: 8250/16550 driver, 10 ports, IRQ sharing disabled
[    1.871745] random: crng init done
[    1.872110] rockchip-vop2 fdd90000.vop: Adding to iommu group 14
[    1.876817] rockchip-vop2 fdd90000.vop: [drm:vop2_bind] vp0 assign plane mask: 0x5, primary plane phy id: 2
[    1.876828] rockchip-vop2 fdd90000.vop: [drm:vop2_bind] vp1 assign plane mask: 0xa, primary plane phy id: 3
[    1.876837] rockchip-vop2 fdd90000.vop: [drm:vop2_bind] vp2 assign plane mask: 0x140, primary plane phy id: 8
[    1.876845] rockchip-vop2 fdd90000.vop: [drm:vop2_bind] vp3 assign plane mask: 0x280, primary plane phy id: 9
[    1.876934] rockchip-vop2 fdd90000.vop: [drm:vop2_bind] Cluster0-win0 as cursor plane for vp0
[    1.877002] rockchip-vop2 fdd90000.vop: [drm:vop2_bind] Cluster1-win0 as cursor plane for vp1
[    1.877064] rockchip-vop2 fdd90000.vop: [drm:vop2_bind] Cluster2-win0 as cursor plane for vp2
[    1.877124] rockchip-vop2 fdd90000.vop: [drm:vop2_bind] Cluster3-win0 as cursor plane for vp3
[    1.877142] [drm] failed to init overlay plane Cluster0-win1
[    1.877147] [drm] failed to init overlay plane Cluster1-win1
[    1.877152] [drm] failed to init overlay plane Cluster2-win1
[    1.877156] [drm] failed to init overlay plane Cluster3-win1
[    1.884446] rockchip-drm display-subsystem: bound fdd90000.vop (ops 0xffffffc00935df48)
[    1.884843] dwhdmi-rockchip fde80000.hdmi: registered ddc I2C bus driver
[    1.885173] rockchip-drm display-subsystem: bound fde80000.hdmi (ops 0xffffffc00936c2a0)
[    1.885227] rockchip-drm display-subsystem: bound fde50000.dp (ops 0xffffffc00936ed28)
[    1.885622] rockchip-drm display-subsystem: route-dp0: failed to get logo,offset
[    1.885633] rockchip-drm display-subsystem: route-hdmi0: failed to get logo,offset
[    1.885640] rockchip-drm display-subsystem: can't not find any logo display
[    1.885647] rockchip-drm display-subsystem: failed to show kernel logo
[    1.885691] rockchip-drm display-subsystem: [drm] Cannot find any crtc or sizes
[    1.885732] rockchip-drm display-subsystem: [drm] Cannot find any crtc or sizes
[    1.885749] rockchip-drm display-subsystem: [drm] Cannot find any crtc or sizes
[    1.886106] [drm] Initialized rockchip 3.0.0 20140818 for display-subsystem on minor 0
[    1.890889] brd: module loaded
[    1.893096] loop: module loaded
[    1.893228] zram: Added device: zram0
[    1.893326] lkdtm: No crash points registered, enable through debugfs
[    1.893424] system_heap: orders[0] = 6
[    1.893429] system_heap: orders[1] = 4
[    1.893433] system_heap: orders[2] = 0
[    1.895099] rockchip-spi feb20000.spi: no high_speed pinctrl state
[    1.896009] rk806 spi2.0: chip id: RK806,ver:0x2, 0x1
[    1.896217] rk806 spi2.0: ON: 0x40 OFF:0x0
[    1.897594] vdd_gpu_s0: supplied by vcc5v0_sys
[    1.898111] vdd_cpu_lit_s0: supplied by vcc5v0_sys
[    1.898555] vdd_log_s0: supplied by vcc5v0_sys
[    1.899047] vdd_vdenc_s0: supplied by vcc5v0_sys
[    1.899589] vdd_ddr_s0: supplied by vcc5v0_sys
[    1.899902] vdd2_ddr_s3: supplied by vcc5v0_sys
[    1.900388] vdd_2v0_pldo_s3: supplied by vcc5v0_sys
[    1.900769] vcc_3v3_s3: supplied by vcc5v0_sys
[    1.901184] vddq_ddr_s0: supplied by vcc5v0_sys
[    1.901687] vcc_1v8_s3: supplied by vcc5v0_sys
[    1.902174] vdd_0v75_s3: supplied by vcc_1v1_nldo_s3
[    1.902664] avdd_ddr_pll_s0: supplied by vcc_1v1_nldo_s3
[    1.903094] avdd_0v75_s0: supplied by vcc_1v1_nldo_s3
[    1.903521] avdd_0v85_s0: supplied by vcc_1v1_nldo_s3
[    1.904036] nldo5_s0: supplied by vcc_1v1_nldo_s3
[    1.904224] vcc_1v8_s0: supplied by vdd_2v0_pldo_s3
[    1.904773] avcc_1v8_s0: supplied by vdd_2v0_pldo_s3
[    1.905340] avdd_1v2_s0: supplied by vdd_2v0_pldo_s3
[    1.905820] avcc_3v3_s0: supplied by vcc5v0_sys
[    1.906246] vccio_sd_s0: supplied by vcc5v0_sys
[    1.906680] pldo6_s3: supplied by vcc5v0_sys
[    1.907086] rk806 spi2.0: no sleep-setting state
[    1.907093] rk806 spi2.0: no reset-setting pinctrl state
[    1.907099] rk806 spi2.0: no dvs-setting pinctrl state
[    1.908313] rockchip-spi feb20000.spi: probed, poll=0, rsd=0
[    1.908872] CAN device driver interface
[    1.909445] rk_gmac-dwmac fe1c0000.ethernet: IRQ eth_lpi not found
[    1.909564] rk_gmac-dwmac fe1c0000.ethernet: no regulator found
[    1.909571] rk_gmac-dwmac fe1c0000.ethernet: clock input or output? (output).
[    1.909577] rk_gmac-dwmac fe1c0000.ethernet: TX delay(0x0).
[    1.909584] rk_gmac-dwmac fe1c0000.ethernet: RX delay(0x1b).
[    1.909597] rk_gmac-dwmac fe1c0000.ethernet: integrated PHY? (no).
[    1.909604] rk_gmac-dwmac fe1c0000.ethernet: cannot get clock mac_clk_rx
[    1.909611] rk_gmac-dwmac fe1c0000.ethernet: cannot get clock mac_clk_tx
[    1.909623] rk_gmac-dwmac fe1c0000.ethernet: cannot get clock clk_mac_speed
[    1.909840] rk_gmac-dwmac fe1c0000.ethernet: init for RGMII_RXID
[    1.909936] rk_gmac-dwmac fe1c0000.ethernet: User ID: 0x30, Synopsys ID: 0x51
[    1.909943] rk_gmac-dwmac fe1c0000.ethernet: 	DWMAC4/5
[    1.909950] rk_gmac-dwmac fe1c0000.ethernet: DMA HW capability register supported
[    1.909956] rk_gmac-dwmac fe1c0000.ethernet: RX Checksum Offload Engine supported
[    1.909962] rk_gmac-dwmac fe1c0000.ethernet: TX Checksum insertion supported
[    1.909968] rk_gmac-dwmac fe1c0000.ethernet: Wake-Up On Lan supported
[    1.909994] rk_gmac-dwmac fe1c0000.ethernet: TSO supported
[    1.910000] rk_gmac-dwmac fe1c0000.ethernet: Enable RX Mitigation via HW Watchdog Timer
[    1.910007] rk_gmac-dwmac fe1c0000.ethernet: Enabled Flow TC (entries=2)
[    1.910013] rk_gmac-dwmac fe1c0000.ethernet: TSO feature enabled
[    1.910019] rk_gmac-dwmac fe1c0000.ethernet: Using 32 bits DMA width
[    2.047943] PPP generic driver version 2.4.2
[    2.048038] PPP BSD Compression module registered
[    2.048044] PPP Deflate Compression module registered
[    2.048055] PPP MPPE Compression module registered
[    2.048060] NET: Registered protocol family 24
[    2.048072] SLIP: version 0.8.4-NET3.019-NEWTTY (dynamic channels, max=256).
[    2.048077] CSLIP: code copyright 1989 Regents of the University of California.
[    2.048103] usbcore: registered new interface driver rndis_wlan
[    2.048121] usbcore: registered new interface driver cdc_ether
[    2.048133] usbcore: registered new interface driver rndis_host
[    2.048147] usbcore: registered new interface driver qmi_wwan
[    2.056034] ehci_hcd: USB 2.0 'Enhanced' Host Controller (EHCI) Driver
[    2.056046] ehci-pci: EHCI PCI platform driver
[    2.056069] ehci-platform: EHCI generic platform driver
[    2.058241] ehci-platform fc800000.usb: EHCI Host Controller
[    2.058313] ehci-platform fc800000.usb: new USB bus registered, assigned bus number 1
[    2.058367] ehci-platform fc800000.usb: irq 20, io mem 0xfc800000
[    2.071226] ehci-platform fc800000.usb: USB 2.0 started, EHCI 1.00
[    2.071289] usb usb1: New USB device found, idVendor=1d6b, idProduct=0002, bcdDevice= 5.10
[    2.071297] usb usb1: New USB device strings: Mfr=3, Product=2, SerialNumber=1
[    2.071304] usb usb1: Product: EHCI Host Controller
[    2.071309] usb usb1: Manufacturer: Linux 5.10.160 ehci_hcd
[    2.071315] usb usb1: SerialNumber: fc800000.usb
[    2.071508] hub 1-0:1.0: USB hub found
[    2.071520] hub 1-0:1.0: 1 port detected
[    2.073792] ehci-platform fc880000.usb: EHCI Host Controller
[    2.073862] ehci-platform fc880000.usb: new USB bus registered, assigned bus number 2
[    2.073908] ehci-platform fc880000.usb: irq 22, io mem 0xfc880000
[    2.084551] ehci-platform fc880000.usb: USB 2.0 started, EHCI 1.00
[    2.084606] usb usb2: New USB device found, idVendor=1d6b, idProduct=0002, bcdDevice= 5.10
[    2.084613] usb usb2: New USB device strings: Mfr=3, Product=2, SerialNumber=1
[    2.084620] usb usb2: Product: EHCI Host Controller
[    2.084626] usb usb2: Manufacturer: Linux 5.10.160 ehci_hcd
[    2.084631] usb usb2: SerialNumber: fc880000.usb
[    2.084791] hub 2-0:1.0: USB hub found
[    2.084803] hub 2-0:1.0: 1 port detected
[    2.085060] ohci_hcd: USB 1.1 'Open' Host Controller (OHCI) Driver
[    2.085070] ohci-platform: OHCI generic platform driver
[    2.085194] ohci-platform fc840000.usb: Generic Platform OHCI controller
[    2.085265] ohci-platform fc840000.usb: new USB bus registered, assigned bus number 3
[    2.085301] ohci-platform fc840000.usb: irq 21, io mem 0xfc840000
[    2.117899] rk-pcie fe190000.pcie: PCIe Link up, LTSSM is 0x30011
[    2.118049] rk-pcie fe190000.pcie: PCI host bridge to bus 0004:40
[    2.118071] pci_bus 0004:40: root bus resource [bus 40-4f]
[    2.118088] pci_bus 0004:40: root bus resource [??? 0xf4000000-0xf40fffff flags 0x0]
[    2.118107] pci_bus 0004:40: root bus resource [io  0x0000-0xfffff] (bus address [0xf4100000-0xf41fffff])
[    2.118126] pci_bus 0004:40: root bus resource [mem 0xf4200000-0xf4ffffff]
[    2.118142] pci_bus 0004:40: root bus resource [mem 0xa00000000-0xa3fffffff pref]
[    2.118187] pci 0004:40:00.0: [1d87:3588] type 01 class 0x060400
[    2.118221] pci 0004:40:00.0: reg 0x38: [mem 0x00000000-0x0000ffff pref]
[    2.118291] pci 0004:40:00.0: supports D1 D2
[    2.118305] pci 0004:40:00.0: PME# supported from D0 D1 D3hot
[    2.128475] pci 0004:40:00.0: Primary bus is hard wired to 0
[    2.128505] pci 0004:40:00.0: bridge configuration invalid ([bus 01-ff]), reconfiguring
[    2.128732] pci 0004:41:00.0: [10ec:c822] type 00 class 0x028000
[    2.128819] pci 0004:41:00.0: reg 0x10: initial BAR value 0x00000000 invalid
[    2.128836] pci 0004:41:00.0: reg 0x10: [io  size 0x0100]
[    2.128935] pci 0004:41:00.0: reg 0x18: [mem 0x00000000-0x0000ffff 64bit]
[    2.129399] pci 0004:41:00.0: supports D1 D2
[    2.129413] pci 0004:41:00.0: PME# supported from D0 D1 D2 D3hot D3cold
[    2.145270] usb usb3: New USB device found, idVendor=1d6b, idProduct=0001, bcdDevice= 5.10
[    2.145280] usb usb3: New USB device strings: Mfr=3, Product=2, SerialNumber=1
[    2.145287] usb usb3: Product: Generic Platform OHCI controller
[    2.145292] usb usb3: Manufacturer: Linux 5.10.160 ohci_hcd
[    2.145298] usb usb3: SerialNumber: fc840000.usb
[    2.147726] pci_bus 0004:41: busn_res: [bus 41-4f] end is updated to 41
[    2.147728] hub 3-0:1.0: USB hub found
[    2.147737] hub 3-0:1.0: 1 port detected
[    2.147767] pci 0004:40:00.0: BAR 8: assigned [mem 0xf4200000-0xf42fffff]
[    2.147790] pci 0004:40:00.0: BAR 6: assigned [mem 0xf4300000-0xf430ffff pref]
[    2.147809] pci 0004:40:00.0: BAR 7: assigned [io  0x1000-0x1fff]
[    2.147829] pci 0004:41:00.0: BAR 2: assigned [mem 0xf4200000-0xf420ffff 64bit]
[    2.147912] pci 0004:41:00.0: BAR 0: assigned [io  0x1000-0x10ff]
[    2.147942] pci 0004:40:00.0: PCI bridge to [bus 41]
[    2.147957] pci 0004:40:00.0:   bridge window [io  0x1000-0x1fff]
[    2.147959] ohci-platform fc8c0000.usb: Generic Platform OHCI controller
[    2.147986] pci 0004:40:00.0:   bridge window [mem 0xf4200000-0xf42fffff]
[    2.148025] ohci-platform fc8c0000.usb: new USB bus registered, assigned bus number 4
[    2.148063] ohci-platform fc8c0000.usb: irq 23, io mem 0xfc8c0000
[    2.150287] pcieport 0004:40:00.0: PME: Signaling with IRQ 119
[    2.208603] usb usb4: New USB device found, idVendor=1d6b, idProduct=0001, bcdDevice= 5.10
[    2.208613] usb usb4: New USB device strings: Mfr=3, Product=2, SerialNumber=1
[    2.208619] usb usb4: Product: Generic Platform OHCI controller
[    2.208625] usb usb4: Manufacturer: Linux 5.10.160 ohci_hcd
[    2.208630] usb usb4: SerialNumber: fc8c0000.usb
[    2.208793] hub 4-0:1.0: USB hub found
[    2.208806] hub 4-0:1.0: 1 port detected
[    2.209188] xhci-hcd xhci-hcd.7.auto: xHCI Host Controller
[    2.209257] xhci-hcd xhci-hcd.7.auto: new USB bus registered, assigned bus number 5
[    2.209323] xhci-hcd xhci-hcd.7.auto: hcc params 0x0220fe64 hci version 0x110 quirks 0x0000200002010010
[    2.209344] xhci-hcd xhci-hcd.7.auto: irq 109, io mem 0xfcd00000
[    2.209434] usb usb5: New USB device found, idVendor=1d6b, idProduct=0002, bcdDevice= 5.10
[    2.209442] usb usb5: New USB device strings: Mfr=3, Product=2, SerialNumber=1
[    2.209448] usb usb5: Product: xHCI Host Controller
[    2.209453] usb usb5: Manufacturer: Linux 5.10.160 xhci-hcd
[    2.209458] usb usb5: SerialNumber: xhci-hcd.7.auto
[    2.209624] hub 5-0:1.0: USB hub found
[    2.209636] hub 5-0:1.0: 1 port detected
[    2.209722] xhci-hcd xhci-hcd.7.auto: xHCI Host Controller
[    2.209781] xhci-hcd xhci-hcd.7.auto: new USB bus registered, assigned bus number 6
[    2.209790] xhci-hcd xhci-hcd.7.auto: Host supports USB 3.0 SuperSpeed
[    2.209810] usb usb6: We don't know the algorithms for LPM for this host, disabling LPM.
[    2.209843] usb usb6: New USB device found, idVendor=1d6b, idProduct=0003, bcdDevice= 5.10
[    2.209850] usb usb6: New USB device strings: Mfr=3, Product=2, SerialNumber=1
[    2.209856] usb usb6: Product: xHCI Host Controller
[    2.209862] usb usb6: Manufacturer: Linux 5.10.160 xhci-hcd
[    2.209867] usb usb6: SerialNumber: xhci-hcd.7.auto
[    2.210017] hub 6-0:1.0: USB hub found
[    2.210028] hub 6-0:1.0: 1 port detected
[    2.210154] usbcore: registered new interface driver cdc_acm
[    2.210160] cdc_acm: USB Abstract Control Model driver for USB modems and ISDN adapters
[    2.210176] usbcore: registered new interface driver cdc_wdm
[    2.210272] usbcore: registered new interface driver uas
[    2.210311] usbcore: registered new interface driver usb-storage
[    2.210646] usbcore: registered new interface driver usbtouchscreen
[    2.210760] .. rk pwm remotectl v2.0 init
[    2.210868] input: febd0030.pwm as /devices/platform/febd0030.pwm/input/input0
[    2.211001] remotectl-pwm febd0030.pwm: pwm version is 0x2130000
[    2.211023] remotectl-pwm febd0030.pwm: Controller support pwrkey capture
[    2.211867] input: rk805 pwrkey as /devices/platform/feb20000.spi/spi_master/spi2/spi2.0/rk805-pwrkey.5.auto/input/input1
[    2.212054] i2c /dev entries driver
[    2.214468] rtc-hym8563 0-0051: rtc information is invalid
[    2.221175] rtc-hym8563 0-0051: registered as rtc0
[    2.222178] rtc-hym8563 0-0051: setting system clock to 2021-01-01T12:00:00 UTC (1609502400)
[    2.226825] vdd_cpu_big0_s0: supplied by vcc5v0_sys
[    2.235234] vdd_cpu_big1_s0: supplied by vcc5v0_sys
[    2.244049] vdd_npu_s0: supplied by vcc5v0_sys
[    2.264364] usbcore: registered new interface driver uvcvideo
[    2.264389] USB Video Class driver (1.1.1)
[    2.267573] cpu cpu0: bin=0
[    2.267778] cpu cpu0: leakage=11
[    2.269345] cpu cpu0: pvtm=1466
[    2.269572] cpu cpu0: pvtm-volt-sel=3
[    2.271884] cpu cpu4: bin=0
[    2.272083] cpu cpu4: leakage=9
[    2.278726] cpu cpu4: pvtm=1701
[    2.282809] cpu cpu4: pvtm-volt-sel=4
[    2.285865] cpu cpu6: bin=0
[    2.286064] cpu cpu6: leakage=9
[    2.292706] cpu cpu6: pvtm=1712
[    2.296784] cpu cpu6: pvtm-volt-sel=5
[    2.299313] cpu cpu0: avs=0
[    2.301075] cpu cpu4: avs=0
[    2.302705] cpu cpu6: avs=0
[    2.303163] cpu cpu0: EM: created perf domain
[    2.303236] cpu cpu0: l=10000 h=85000 hyst=5000 l_limit=0 h_limit=1608000000 h_table=0
[    2.304288] cpu cpu4: EM: created perf domain
[    2.304349] cpu cpu4: l=10000 h=85000 hyst=5000 l_limit=0 h_limit=2208000000 h_table=0
[    2.312956] cpu cpu6: EM: created perf domain
[    2.313547] cpu cpu6: l=10000 h=85000 hyst=5000 l_limit=0 h_limit=2208000000 h_table=0
[    2.326691] sdhci: Secure Digital Host Controller Interface driver
[    2.326711] sdhci: Copyright(c) Pierre Ossman
[    2.326718] Synopsys Designware Multimedia Card Interface Driver
[    2.327058] sdhci-pltfm: SDHCI platform and OF driver helper
[    2.328113] arm-scmi firmware:scmi: Failed. SCMI protocol 17 not active.
[    2.328154] SMCCC: SOC_ID: ARCH_SOC_ID not implemented, skipping ....
[    2.328571] cryptodev: driver 1.12 loaded.
[    2.328605] hid: raw HID events driver (C) Jiri Kosina
[    2.328741] usbcore: registered new interface driver usbhid
[    2.328749] usbhid: USB HID core driver
[    2.333702] optee: probing for conduit method.
[    2.333727] optee: revision 3.13 (b5340fd6)
[    2.333918] optee: dynamic shared memory is enabled
[    2.334037] optee: initialized driver
[    2.334458] usbcore: registered new interface driver snd-usb-audio
[    2.334593] usb 2-1: new high-speed USB device number 2 using ehci-platform
[    2.339145] debugfs: File 'Capture' in directory 'dapm' already present!
[    2.340327] input: rockchip,dp0 rockchip,dp0 as /devices/platform/dp0-sound/sound/card0/input2
[    2.341456] input: rockchip-hdmi0 rockchip-hdmi0 as /devices/platform/hdmi0-sound/sound/card1/input3
[    2.342214] input: headset-keys as /devices/platform/es8388-sound/input/input4
[    2.351869] ES8323 7-0011: ASoC: error at soc_component_write_no_lock on ES8323.7-0011: -5
[    2.357209] mmc0: SDHCI controller on fe2e0000.mmc [fe2e0000.mmc] using ADMA
[    2.395143] mmc0: Host Software Queue enabled
[    2.395182] mmc0: new HS400 Enhanced strobe MMC card at address 0001
[    2.395730] mmcblk0: mmc0:0001 SJ8311 117 GiB 
[    2.395914] mmcblk0boot0: mmc0:0001 SJ8311 partition 1 4.00 MiB
[    2.396095] mmcblk0boot1: mmc0:0001 SJ8311 partition 2 4.00 MiB
[    2.396354] mmcblk0rpmb: mmc0:0001 SJ8311 partition 3 4.00 MiB, chardev (236:0)
[    2.399648]  mmcblk0: p1 p2 p3
[    2.402346] input: rockchip-es8388 Headset as /devices/platform/es8388-sound/sound/card2/input5
[    2.404039] xt_time: kernel timezone is -0000
[    2.404089] IPVS: Registered protocols ()
[    2.404108] IPVS: Connection hash table configured (size=4096, memory=32Kbytes)
[    2.404188] IPVS: ipvs loaded.
[    2.404334] Initializing XFRM netlink socket
[    2.404609] NET: Registered protocol family 10
[    2.405081] Segment Routing with IPv6
[    2.405200] NET: Registered protocol family 17
[    2.405217] NET: Registered protocol family 15
[    2.405246] Bridge firewalling registered
[    2.405253] can: controller area network core
[    2.405277] NET: Registered protocol family 29
[    2.405284] can: raw protocol
[    2.405291] can: broadcast manager protocol
[    2.405301] can: netlink gateway - max_hops=1
[    2.405373] 8021q: 802.1Q VLAN Support v1.8
[    2.405388] [BT_RFKILL]: Enter rfkill_rk_init
[    2.405395] [WLAN_RFKILL]: Enter rfkill_wlan_init
[    2.405738] Key type dns_resolver registered
[    2.406564] Loading compiled-in X.509 certificates
[    2.407238] pstore: Using crash dump compression: deflate
[    2.407518] rga3_core0 fdb60000.rga: Adding to iommu group 2
[    2.407712] rga: rga3_core0, irq = 35, match scheduler
[    2.408020] rga: rga3_core0 hardware loaded successfully, hw_version:3.0.76831.
[    2.408077] rga: rga3_core0 probe successfully
[    2.408409] rga3_core1 fdb70000.rga: Adding to iommu group 3
[    2.408584] rga: rga3_core1, irq = 36, match scheduler
[    2.408897] rga: rga3_core1 hardware loaded successfully, hw_version:3.0.76831.
[    2.408939] rga: rga3_core1 probe successfully
[    2.409218] rga: rga2, irq = 37, match scheduler
[    2.409503] rga: rga2 hardware loaded successfully, hw_version:3.2.63318.
[    2.409516] rga: rga2 probe successfully
[    2.409688] rga_iommu: IOMMU binding successfully, default mapping core[0x1]
[    2.409862] rga: Module initialized. v1.2.27
[    2.430682] vendor storage:20190527 ret = 0
[    2.436451] combophy_avdd0v85: supplied by avdd_0v85_s0
[    2.436727] mali fb000000.gpu: Kernel DDK version g18p0-01eac0
[    2.437048] combophy_avdd1v8: supplied by avcc_1v8_s0
[    2.437505] vcc_3v3_s0: supplied by vcc_3v3_s3
[    2.437803] vcc_3v3_sd_s3: supplied by vcc_3v3_s3
[    2.438447] mali fb000000.gpu: bin=0
[    2.438629] mali fb000000.gpu: leakage=17
[    2.438672] debugfs: Directory 'fb000000.gpu-mali' with parent 'vdd_gpu_s0' already present!
[    2.439166] rockchip-dmc dmc: leakage=36
[    2.439182] rockchip-dmc dmc: leakage-volt-sel=1
[    2.439913] rockchip-dmc dmc: avs=0
[    2.439928] rockchip-dmc dmc: current ATF version 0x100
[    2.440018] rockchip-dmc dmc: normal_rate = 1560000000
[    2.440029] rockchip-dmc dmc: reboot_rate = 2112000000
[    2.440038] rockchip-dmc dmc: suspend_rate = 528000000
[    2.440047] rockchip-dmc dmc: video_4k_rate = 1560000000
[    2.440055] rockchip-dmc dmc: video_4k_10b_rate = 1560000000
[    2.440064] rockchip-dmc dmc: video_svep_rate = 1560000000
[    2.440073] rockchip-dmc dmc: boost_rate = 2112000000
[    2.440082] rockchip-dmc dmc: fixed_rate(isp|cif0|cif1|dualview) = 2112000000
[    2.440091] rockchip-dmc dmc: performance_rate = 2112000000
[    2.440100] rockchip-dmc dmc: hdmirx_rate = 2112000000
[    2.440112] rockchip-dmc dmc: failed to get vop bandwidth to dmc rate
[    2.440120] rockchip-dmc dmc: failed to get vop pn to msch rl
[    2.440222] rockchip-dmc dmc: l=10000 h=2147483647 hyst=5000 l_limit=0 h_limit=0 h_table=0
[    2.440260] mali fb000000.gpu: pvtm=890
[    2.440275] rockchip-dmc dmc: could not find power_model node
[    2.440379] mali fb000000.gpu: pvtm-volt-sel=4
[    2.441126] input: adc-keys as /devices/platform/adc-keys/input/input6
[    2.441554] mali fb000000.gpu: avs=0
[    2.441669] W : [File] : drivers/gpu/arm/bifrost/platform/rk/mali_kbase_config_rk.c; [Line] : 143; [Func] : kbase_platform_rk_init(); power-off-delay-ms not available.
[    2.442128] mali fb000000.gpu: r0p0 status 5 not found in HW issues table;
[    2.442142] mali fb000000.gpu: falling back to closest match: r0p0 status 0
[    2.442151] mali fb000000.gpu: Execution proceeding normally with fallback match
[    2.442164] mali fb000000.gpu: GPU identified as 0x7 arch 10.8.6 r0p0 status 0
[    2.442235] mali fb000000.gpu: No priority control manager is configured
[    2.442420] mali fb000000.gpu: No memory group manager is configured
[    2.442457] mali fb000000.gpu: Protected memory allocator not available
[    2.442637] dwmmc_rockchip fe2c0000.mmc: No normal pinctrl state
[    2.442652] dwmmc_rockchip fe2c0000.mmc: No idle pinctrl state
[    2.442771] dwmmc_rockchip fe2c0000.mmc: IDMAC supports 32-bit address mode.
[    2.442849] dwmmc_rockchip fe2c0000.mmc: Using internal DMA controller.
[    2.442872] dwmmc_rockchip fe2c0000.mmc: Version ID is 270a
[    2.442931] dwmmc_rockchip fe2c0000.mmc: DW MMC controller at irq 79,32 bit host data width,256 deep fifo
[    2.443329] mali fb000000.gpu: Capping CSF_FIRMWARE_TIMEOUT to CSF_FIRMWARE_PING_TIMEOUT
[    2.443740] mali fb000000.gpu: l=10000 h=85000 hyst=5000 l_limit=0 h_limit=800000000 h_table=0
[    2.444437] mali fb000000.gpu: Probed as mali0
[    2.445086] RKNPU fdab0000.npu: Adding to iommu group 0
[    2.445276] RKNPU fdab0000.npu: RKNPU: rknpu iommu is enabled, using iommu mode
[    2.446560] RKNPU fdab0000.npu: can't request region for resource [mem 0xfdab0000-0xfdabffff]
[    2.446593] RKNPU fdab0000.npu: can't request region for resource [mem 0xfdac0000-0xfdacffff]
[    2.446616] RKNPU fdab0000.npu: can't request region for resource [mem 0xfdad0000-0xfdadffff]
[    2.446978] [drm] Initialized rknpu 0.8.8 20230428 for fdab0000.npu on minor 1
[    2.450487] RKNPU fdab0000.npu: RKNPU: bin=0
[    2.450677] RKNPU fdab0000.npu: leakage=9
[    2.450731] debugfs: Directory 'fdab0000.npu-rknpu' with parent 'vdd_npu_s0' already present!
[    2.456282] mmc_host mmc1: Bus speed (slot 0) = 400000Hz (slot req 400000Hz, actual 400000HZ div = 0)
[    2.457405] RKNPU fdab0000.npu: pvtm=890
[    2.461959] RKNPU fdab0000.npu: pvtm-volt-sel=4
[    2.463251] RKNPU fdab0000.npu: avs=0
[    2.463458] RKNPU fdab0000.npu: l=10000 h=85000 hyst=5000 l_limit=0 h_limit=800000000 h_table=0
[    2.470935] RKNPU fdab0000.npu: failed to find power_model node
[    2.470979] RKNPU fdab0000.npu: RKNPU: failed to initialize power model
[    2.470995] RKNPU fdab0000.npu: RKNPU: failed to get dynamic-coefficient
[    2.472041] cfg80211: Loading compiled-in X.509 certificates for regulatory database
[    2.482144] cfg80211: Loaded X.509 cert 'sforshee: 00b28ddf47aef9cea7'
[    2.484372] I : [File] : drivers/gpu/arm/mali400/mali/linux/mali_kernel_linux.c; [Line] : 406; [Func] : mali_module_init(); svn_rev_string_from_arm of this mali_ko is '', rk_ko_ver is '5', built at '00:58:48', on 'Dec 10 2023'.
[    2.484793] Mali: 
[    2.484796] Mali device driver loaded
[    2.484816] ALSA device list:
[    2.484825]   #0: rockchip,dp0
[    2.484833]   #1: rockchip-hdmi0
[    2.484841]   #2: rockchip-es8388
[    2.488406] Freeing unused kernel memory: 6272K
[    2.488662] platform regulatory.0: Direct firmware load for regulatory.db failed with error -2
[    2.488679] cfg80211: failed to load regulatory.db
[    2.488695] usb 2-1: New USB device found, idVendor=1a86, idProduct=8091, bcdDevice= 2.20
[    2.488713] usb 2-1: New USB device strings: Mfr=0, Product=2, SerialNumber=0
[    2.488723] usb 2-1: Product: USB HUB
[    2.489278] hub 2-1:1.0: USB hub found
[    2.489453] hub 2-1:1.0: 4 ports detected
[    2.504837] Run /init as init process
[    2.545943] mmc_host mmc1: Bus speed (slot 0) = 198000000Hz (slot req 200000000Hz, actual 198000000HZ div = 0)
[    2.759413] dwmmc_rockchip fe2c0000.mmc: Successfully tuned phase to 360
[    2.759477] mmc1: new ultra high speed SDR104 SDXC card at address aaaa
[    2.760087] mmcblk1: mmc1:aaaa SD256 238 GiB 
[    2.763438]  mmcblk1: p1
[    2.771247] usb 2-1.2: new full-speed USB device number 3 using ehci-platform
[    2.871929] usb 2-1.2: New USB device found, idVendor=25a7, idProduct=fa61, bcdDevice= 6.23
[    2.872027] usb 2-1.2: New USB device strings: Mfr=1, Product=2, SerialNumber=0
[    2.872058] usb 2-1.2: Product: 2.4G Receiver
[    2.872081] usb 2-1.2: Manufacturer: Compx
[    2.876065] input: Compx 2.4G Receiver as /devices/platform/fc880000.usb/usb2/2-1/2-1.2/2-1.2:1.0/0003:25A7:FA61.0001/input/input7
[    2.932319] hid-generic 0003:25A7:FA61.0001: input,hidraw0: USB HID v1.10 Keyboard [Compx 2.4G Receiver] on usb-fc880000.usb-1.2/input0
[    2.937235] input: Compx 2.4G Receiver Mouse as /devices/platform/fc880000.usb/usb2/2-1/2-1.2/2-1.2:1.1/0003:25A7:FA61.0002/input/input8
[    2.991884] input: Compx 2.4G Receiver as /devices/platform/fc880000.usb/usb2/2-1/2-1.2/2-1.2:1.1/0003:25A7:FA61.0002/input/input9
[    2.992968] input: Compx 2.4G Receiver Consumer Control as /devices/platform/fc880000.usb/usb2/2-1/2-1.2/2-1.2:1.1/0003:25A7:FA61.0002/input/input10
[    2.993877] input: Compx 2.4G Receiver System Control as /devices/platform/fc880000.usb/usb2/2-1/2-1.2/2-1.2:1.1/0003:25A7:FA61.0002/input/input11
[    2.995835] hid-generic 0003:25A7:FA61.0002: input,hiddev96,hidraw1: USB HID v1.10 Mouse [Compx 2.4G Receiver] on usb-fc880000.usb-1.2/input1
[    3.084769] usb 2-1.4: new full-speed USB device number 4 using ehci-platform
[    3.185009] usb 2-1.4: New USB device found, idVendor=0bda, idProduct=c822, bcdDevice= 0.00
[    3.185108] usb 2-1.4: New USB device strings: Mfr=1, Product=2, SerialNumber=3
[    3.185154] usb 2-1.4: Product: Bluetooth Radio 
[    3.185188] usb 2-1.4: Manufacturer: Realtek 
[    3.185222] usb 2-1.4: SerialNumber: 00e04c000001
[    3.308313] EXT4-fs (mmcblk0p3): mounted filesystem with ordered data mode. Opts: (null)
[    3.517032] systemd[1]: System time before build time, advancing clock.
[    3.534075] systemd[1]: Failed to find module 'autofs4'
[    3.592207] systemd-fstab-generator[307]: Ignoring "noauto" for root device
[    3.993102] EXT4-fs (mmcblk0p3): re-mounted. Opts: (null)
[    4.109983] systemd-journald[337]: Received client request to flush runtime journal.
[    4.112210] systemd-journald[337]: File /var/log/journal/2ca62aa618544cd59bcbf96445382dc4/system.journal corrupted or uncleanly shut down, renaming and replacing.
[    4.343592] Bluetooth: Core ver 2.22
[    4.343654] NET: Registered protocol family 31
[    4.343663] Bluetooth: HCI device and connection manager initialized
[    4.343677] Bluetooth: HCI socket layer initialized
[    4.343687] Bluetooth: L2CAP socket layer initialized
[    4.343702] Bluetooth: SCO socket layer initialized
[    4.354114] usbcore: registered new interface driver btusb
[    4.369043] rtw_8822ce 0004:41:00.0: of_irq_parse_pci: failed with rc=134
[    4.369153] rtw_8822ce 0004:41:00.0: can't change power state from D3cold to D0 (config space inaccessible)
[    4.378936] rtw_8822ce 0004:41:00.0: mac power on failed
[    4.378949] rtw_8822ce 0004:41:00.0: failed to power on mac
[    4.378952] rtw_8822ce 0004:41:00.0: failed to setup chip efuse info
[    4.378955] rtw_8822ce 0004:41:00.0: failed to setup chip information
[    4.380963] usb 2-1.4: USB disconnect, device number 4
[    4.407811] rtw_8822ce 0004:41:00.0: Firmware version 9.9.4, H2C version 15
[    4.407913] rtw_8822ce 0004:41:00.0: Firmware version 9.9.14, H2C version 15
[    4.408018] rtw_8822ce: probe of 0004:41:00.0 failed with error -114
[    4.464612] RTW: module init start
[    4.464631] RTW: rtl88x2ce v5.14.0.0a-4-g81e5f288f.20210817
[    4.464635] RTW: build time: Dec 10 2023 00:58:48
[    4.464639] RTW: rtl88x2ce BT-Coex version = COEX20210504-2323
[    4.464664] RTW: rtw_inetaddr_notifier_register
[    4.464747] rtl88x2ce 0004:41:00.0: of_irq_parse_pci: failed with rc=134
[    4.464760] rtl88x2ce 0004:41:00.0: can't change power state from D3cold to D0 (config space inaccessible)
[    4.464767] RTW: PCIE: Using 32bit DMA
[    4.464783] RTW: Memory mapped space start: 0xf4200000 len:00010000 flags:00140204, after map:0xffffffc00d180000
[    4.464787] RTW: CHIP TYPE: RTL8822CE
[    4.464791] RTW: Bus master is enabled. usPciCommand=ffff
[    4.464794] RTW: INTDIS==1 usPciCommand=ffff
[    4.464798] RTW: pci_write_config_word (Command) Result=134
[    4.464801] RTW: ERROR PCI parse configuration error
[    4.464832] RTW: module init ret=0
[    4.558925] EXT4-fs (mmcblk0p2): mounting ext2 file system using the ext4 subsystem
[    4.561530] EXT4-fs (mmcblk0p2): mounted filesystem without journal. Opts: (null)
[    4.561572] ext2 filesystem being mounted at /boot supports timestamps until 2038 (0x7fffffff)
[    5.042421] using random self ethernet address
[    5.042449] using random host ethernet address
[    5.051155] usb0: HOST MAC be:f0:6d:86:d0:31
[    5.051196] usb0: MAC d2:53:65:69:ed:e7
[    5.183315] android_work: did not send uevent (0 0 0000000000000000)
[    5.194627] android_work: did not send uevent (0 0 0000000000000000)
[    5.208443] rk_gmac-dwmac fe1c0000.ethernet eth0: PHY [stmmac-1:01] driver [JL2xxx Gigabit Ethernet 1.2.9] (irq=POLL)
[    5.624458] systemd-journald[337]: File /var/log/journal/2ca62aa618544cd59bcbf96445382dc4/user-1000.journal corrupted or uncleanly shut down, renaming and replacing.
[    5.628694] ttyFIQ ttyFIQ0: tty_port_close_start: tty->count = 1 port count = 2
[    6.534678] Bluetooth: hci0: command 0x1001 tx timeout


Debian GNU/Linux 11 lubancat ttyFIQ0

[username:password] root:root cat:temppwd

Modify information : /etc/issue

lubancat login: [    6.721896] dwmac4: Master AXI performs any burst length
[    6.721925] rk_gmac-dwmac fe1c0000.ethernet eth0: No Safety Features support found
[    6.721949] rk_gmac-dwmac fe1c0000.ethernet eth0: IEEE 1588-2008 Advanced Timestamp supported
[    6.722236] rk_gmac-dwmac fe1c0000.ethernet eth0: registered PTP clock
[    6.722572] rk_gmac-dwmac fe1c0000.ethernet eth0: configuring for phy/rgmii-rxid link mode
[    6.723135] 8021q: adding VLAN 0 to HW filter on device eth0
[    7.322497] mali fb000000.gpu: Loading Mali firmware 0x1010000
[    7.325230] mali fb000000.gpu: Mali firmware git_sha: ee476db42870778306fa8d559a605a73f13e455c 
[    8.136149] android_work: did not send uevent (0 0 0000000000000000)
[   14.428668] Bluetooth: hci0: RTL: HCI_OP_READ_LOCAL_VERSION failed (-110)
[   14.635481] usb 2-1.4: new full-speed USB device number 5 using ehci-platform
[   14.740643] usb 2-1.4: New USB device found, idVendor=0bda, idProduct=c822, bcdDevice= 0.00
[   14.740684] usb 2-1.4: New USB device strings: Mfr=1, Product=2, SerialNumber=3
[   14.740691] usb 2-1.4: Product: Bluetooth Radio 
[   14.740697] usb 2-1.4: Manufacturer: Realtek 
[   14.740703] usb 2-1.4: SerialNumber: 00e04c000001
[   14.744355] Bluetooth: hci0: RTL: examining hci_ver=0a hci_rev=000c lmp_ver=0a lmp_subver=8822
[   14.746349] Bluetooth: hci0: RTL: rom_version status=0 version=3
[   14.746357] Bluetooth: hci0: RTL: loading rtl_bt/rtl8822cu_fw.bin
[   14.747982] Bluetooth: hci0: RTL: loading rtl_bt/rtl8822cu_config.bin
[   14.748180] Bluetooth: hci0: RTL: cfg_sz 6, total sz 35990
[   15.131840] usb 2-1.4: USB disconnect, device number 5
[   16.989003] Bluetooth: hci0: command 0xfc20 tx timeout
[   25.096285] Bluetooth: hci0: RTL: download fw command failed (-110)
[   25.309641] usb 2-1.4: new full-speed USB device number 6 using ehci-platform
[   25.408133] usb 2-1.4: New USB device found, idVendor=0bda, idProduct=c822, bcdDevice= 0.00
[   25.408165] usb 2-1.4: New USB device strings: Mfr=1, Product=2, SerialNumber=3
[   25.408172] usb 2-1.4: Product: Bluetooth Radio 
[   25.408177] usb 2-1.4: Manufacturer: Realtek 
[   25.408183] usb 2-1.4: SerialNumber: 00e04c000001
[   25.410369] Bluetooth: hci0: RTL: examining hci_ver=0a hci_rev=000c lmp_ver=0a lmp_subver=8822
[   25.411360] Bluetooth: hci0: RTL: rom_version status=0 version=3
[   25.411379] Bluetooth: hci0: RTL: loading rtl_bt/rtl8822cu_fw.bin
[   25.411564] Bluetooth: hci0: RTL: loading rtl_bt/rtl8822cu_config.bin
[   25.411646] Bluetooth: hci0: RTL: cfg_sz 6, total sz 35990
[   25.911470] Bluetooth: hci0: RTL: fw version 0x0cc6d2e3
[   33.417366] nldo5_s0: disabling
[   33.417835] combophy_avdd0v85: disabling
[   33.417847] combophy_avdd1v8: disabling
